Bathtub installation in Houston, drain, overflow and faucet done right

Bathtub installation in Houston is the work of a drain, an overflow and a faucet connection, not just a tub in a hole. A new bathtub is a drain, an overflow and a faucet connection, not just a tub in a hole. El Primo Lalo Plumbing installs bathtubs in Houston with the drain sloped right, the overflow sealed, and the faucet tested, so the floor underneath stays dry.

Bathtub Installation in Houston, Texas
  • New bathtubs
  • Drain and overflow
  • Faucet tested
  • Written scope firstYou approve the price before we start
  • Tested before we leaveEvery repair gets a pressure or flow test
  • Parts on the truckCommon fittings stocked for one-visit repairs
  • Clean work areaWe haul away old parts and debris

What our bathtub installation services Houston include

Every standard install includes removal, haul-off, a new drain and overflow gasket set, and a level set on a proper base. Here's what's covered and what we quote separately if your job needs it.

  • Old tub removal and haul-offWe disconnect the drain and overflow, cut the old tub out if it's cast iron, and haul it away. You're not left with a tub in the yard or a pile of debris in the hall.
  • Subfloor inspectionWith the tub out we check for soft spots and water damage. If the subfloor needs repair, we tell you before we set the new tub and quote it separately.
  • New drain and overflow gasketsWe replace the shoe gasket and overflow gasket on every install. These are the two most common leak points on a tub, and reusing old ones is how a new tub starts leaking in a year.
  • Level set on mortar or foamWe bed the tub on mortar or structural foam so the base is solid. A tub set on bare subfloor flexes and cracks the caulk line. The bed keeps it level and quiet.
  • Supply line and valve checkWe check the shutoff valves and supply lines while the wall is open. If a valve is seized or a line is corroded, we replace it so the next repair doesn't mean opening the wall again.
  • Fill, drain, and leak testBefore we leave we fill the tub, drain it, and check every joint for weeping. Then we run the shower and check the surround. You see the test before we pack up.
Bathtub Installation
Careful professional plumbing work in Houston

Bathtub installation for homes

We swap tubs in houses, condos, and townhomes across Houston. You get the old unit removed, the subfloor checked, and the new tub set level with new gaskets.

  • Alcove and drop-in tub swaps
  • Cast iron tub removal and haul-off
  • Walk-in tub installs with pump
  • Freestanding tub drain relocation

Bathtub installation for businesses

We replace tubs in rental units, apartment complexes, and assisted-living facilities on a schedule that keeps downtime low. Each unit is tested before we move to the next.

  • ApartmentsMulti-unit swaps scheduled one at a time
  • HotelsTub replacement with minimal room downtime
  • Assisted livingWalk-in tubs with pump and door seal checks
  • RentalsFast single-visit swaps for occupied units

Bathtub Installation in Houston: Three Connections, One Test

A bathtub install has three connections that all have to be right: the drain, the overflow and the faucet. The drain has to be vented and sloped, the overflow gasket has to seal, and the faucet has to shut off fully. A failure in any one of them shows up as a slow drain, water on the floor, or a drip that never stops.

Bath remodels drive most bathtub installs in Houston, especially in older homes in the Heights, Montrose and River Oaks. In slab homes, the drain work can mean concrete work, so we check the existing connections before the new tub arrives. Hard water makes a serviceable faucet cartridge worth choosing at install time.

Drain, overflow, faucet. Get all three right and the tub is done for years.

How our bathtub replacement Houston TX process runs

Five steps, one visit for most standard swaps. Here's exactly what happens from the phone call to the first shower.

  1. Phone assessment

    Phone assessment

    We ask the tub type, the alcove measurements, and whether the drain is on the left, right, or center. That tells us what tub fits and whether we need a different rough-in. You get a price range on the call, not a vague 'we'll see when we get there.'

  2. Protect and disconnect

    Protect and disconnect

    We lay down floor protection, shut off the supply, and disconnect the drain and overflow. The old tub comes out in one piece or cut into sections if it's cast iron. Most removals take 45 minutes to two hours depending on weight and access.

  3. Inspect the rough-in

    Inspect the rough-in

    With the tub out we check the subfloor for soft spots, look at the P-trap and drain alignment, and test the shutoff valves. If the subfloor is soft we tell you before we set anything. If the drain needs to move, we quote it before doing the work.

  4. Set and seal the new tub

    Set and seal the new tub

    We bed the tub on mortar or foam, set it level, connect the drain and overflow with new gaskets, and hook up the supply lines. The surround or tile goes back, and we caulk the seams. A standard alcove swap runs three to five hours.

  5. Test and walkthrough

    Test and walkthrough

    We fill the tub, drain it, and check every joint for weeping. Then we run the shower and check the surround. You get a walkthrough of what we did, what to watch for, and how long to let the caulk cure before the first bath.

Tools and methods we use on tub installs

  • Plumbing in Houston

    drain snake and auger

    Clears hair and soap scum from the P-trap and drain line before the new tub is set, so it drains fast from day one.

  • Slab leak under the foundation with no visible signs

    Pipe cutter and tube cutter

    Cuts copper and PEX cleanly when a supply line or drain has to be moved for the new tub.

  • Sewer backup caused by root intrusion in the main line

    Press fitting tool

    Makes leak-free copper and PEX connections in tight spaces behind the tub without soldering near framing.

  • No hot water or a leaking water heater tank

    Propane torch and pipe solder

    Used for copper supply line connections where soldering is the right method and access allows it.

  • Low water pressure throughout the house

    Leak detection microphone

    Finds hidden leaks in the wall or under the floor before we open anything up, so we fix the actual source.

  • Frozen or burst pipe after a hard freeze in Houston

    Sewer camera

    Checks the drain line under the tub for root intrusion or a break before the new tub goes in.

  • Local plumbing service area in Houston

    , , and fixtures

    Tub fillers and shower valves we install and set at the right height for the new tub.

  • Plumbing work in progress in Houston

    2021 Uniform Plumbing Code with Houston Amendments

    We size the drain and overflow and check venting to the 2021 UPC with Houston Amendments. That keeps the install code-correct if you sell the house or get inspected.

When to schedule a tub replacement

  • The tub is 25 years old and the finish is worn through to the fiberglass.

    We remove the old unit, check the subfloor and drain, and set a new acrylic or cast iron tub. We match the drain location so the surround doesn't have to be rebuilt. A clean, solid tub that's usable the same day, with the old one hauled off.

  • A family member needs a walk-in tub for safety and accessibility.

    We measure the rough opening, confirm the drain location, and install the walk-in tub with the right fill and drain valves. We coordinate the electrical for the pump. A walk-in tub that fills and drains correctly, with the door seal tested before we leave.

  • A bathroom remodel is moving the tub to a new location.

    We relocate the drain and supply lines, set the new tub, and tie the overflow and drain back in. We check the venting so the new location drains properly. A tub in the new spot that drains fast and doesn't gurgle, with the old drain capped off.

  • A rental property has a cracked tub and the tenant needs it fixed fast.

    We schedule the swap for a single visit, protect the floor, and haul the old tub off. The tenant has a working tub the same day for most standard swaps. A code-correct install with minimal downtime for the tenant and a clean unit for the owner.

How Bathtub Installation Works in Houston

Bath remodels in the Heights, Montrose and River Oaks drive most installs, while Sharpstown and Meyerland bring slab-home drain work. Hard water makes the faucet cartridge choice matter.

  • The HeightsBungalow bath remodels where the drain, overflow and faucet are renewed together.
  • MontroseBath remodels in older homes where the drain and overflow need attention with the new tub.
  • River OaksHigh-end bath remodels where the install has to be invisible and the seal perfect.
  • MemorialFamily bath upgrades; the tub works all day, so the install has to be right.
  • Garden OaksMid-century bath refreshes with new drain and overflow connections.
  • Hard waterAbout 8 grains per gallon on average, so the faucet cartridge needs to be serviceable.

From problem to finished result.

  • Rusted cast iron tub in the Heights

    Before

    A 1950s cast iron tub was rusted through at the drain and leaking into the ceiling below. The subfloor around the drain was soft, and the surround tile was cracked at the seam.

    After

    We cut the old tub out, repaired the subfloor, and set a new acrylic alcove tub on a mortar bed with new drain and overflow gaskets. The surround was re-caulked and the ceiling below was dry after the fill and drain test.

    Keep the caulk line dry between uses and re-caulk every three to five years. Check the overflow gasket if you see a water stain below.

  • Walk-in tub for an aging parent in Bellaire

    Before

    The family needed a walk-in tub for an aging parent, but the existing alcove was a standard 60-inch tub and the door seal on the old unit was failing. The drain was on the wrong side for the new tub.

    After

    We relocated the drain, set the walk-in tub, and coordinated the electrical for the pump. The fill and drain times were tested and the door seal was checked before we left. The tub fills in under four minutes.

    Run the pump cycle weekly to keep the lines clear. Check the door seal for wear every few months and keep the drain screen clean.

  • Cracked fiberglass tub in a Midtown rental

    Before

    A rental unit had a cracked fiberglass tub that flexed at the base and leaked into the unit below. The tenant needed a working tub fast, and the owner wanted minimal downtime.

    After

    We removed the cracked unit, checked the subfloor, and set a new tub on a foam bed in a single visit. The drain was tested and the unit was back in service the same day. The leak into the unit below stopped.

    Use a drain screen to catch hair and avoid standing on the tub rim. Check the caulk line once a year and re-caulk if it pulls away.

Common tub problems we solve in Houston

Most tub calls come down to a handful of failures. Here's what we see most often and how we fix it.

  • Rusted cast iron tub leaking at the drain

    Rusted cast iron tub leaking at the drain

    We cut the old cast iron tub out, inspect and repair the subfloor, and set a new tub with new drain and overflow gaskets. The old tub gets hauled off before we leave. The leak rots the subfloor and stains the ceiling below. Left alone it can soften the floor enough that the tub starts to move when you step in.

  • Cracked fiberglass tub flexing at the base

    Cracked fiberglass tub flexing at the base

    We remove the cracked unit and set the new tub on a mortar or foam bed so it doesn't flex. The caulk line stays tight and the surround stays dry. A flexing base cracks the caulk line and eventually cracks the tub itself. Water gets behind the surround and into the wall.

  • Slow or gurgling tub drain after a remodel

    Slow or gurgling tub drain after a remodel

    We check the P-trap alignment and venting before the new tub goes in. If the drain has to move, we quote it first and do it right so the tub drains fast. A drain that wasn't aligned right or a trap that wasn't vented properly will back up and gurgle. It's a sign the rough-in wasn't done correctly.

  • Walk-in tub that fills or drains too slowly

    Walk-in tub that fills or drains too slowly

    We size the fill valve and drain for the tub, check the pump circuit, and test the fill and drain times before we leave. The tub works the way it's supposed to. A walk-in tub with the wrong valve or a restricted drain is frustrating and can be a safety issue for someone who needs it.

A level tub with new gaskets, tested before we leave.

  • Stops hidden drain leaks

    Most tub failures start at the overflow or shoe gasket, not the tub itself. When we set a new tub we replace both gaskets and pressure-test the drain before the surround goes back. That's the difference between a dry ceiling below and a water stain you find three months later.

  • Level base, no flex

    A tub set on bare subfloor flexes every time you step in, and flex cracks the caulk line within a year. We bed the tub on mortar or structural foam so the base is solid. You'll feel the difference the first time you stand in it, and the caulk joint stays tight.

  • Code-correct drain and overflow

    Houston follows the 2021 Uniform Plumbing Code with Houston Amendments on tub drains and overflow sizing. We size the drain, set the overflow at the right height, and make sure the trap is properly vented. That keeps the install clean if you ever sell or get inspected.

  • Walk-in tubs done safely

    Walk in bathtub installation Houston Texas jobs need more than a bigger opening. The door seal, the fill and drain speed, and the dedicated circuit for the pump all have to be right. We handle the plumbing side and coordinate the electrical so the tub fills and drains correctly from day one.

What you receive

Clear records you can keep and share.

Written scope

What's included and what's quoted separately

Old tub haul-off

Removed and taken away before we leave

Fill and drain test

Every joint checked before we leave

What to know before you replace a tub

The tub is only half the job. The base it sits on and the gaskets under it decide whether it leaks in a year or lasts a decade.

  • Base matters

    A tub set on bare subfloor flexes and cracks the caulk line. A mortar or foam bed keeps it solid and quiet.

  • Gaskets wear out

    The shoe and overflow gaskets are the most common leak points. We replace both on every install, not just when they look bad.

  • Drain alignment

    If the new tub's drain doesn't line up with the rough-in, the drain has to move. We check that before we quote the job.

Local service area

Plumbing coverage in Houston

Outside these areas? Call and ask if we can reach you. (346) 776-8560

What Houston customers say

  • I can't say enough about their service. They are prompt and responsive to questions. Attentive to cleaning up afterwards and wear shoe covers. Prices are good and he helped me choose compatible replacement faucet and garbage disposal. which I ran out and picked up while he did other repairs. Fransisco is such a kind person and my elderly mom has been so pleased.
    Ann BogranGoogle review
  • I'm very happy with your service. He is very efficient and knowledgeable thank you primo Lalo!!!
    Naty MaqueiraGoogle review
  • I will definitely recommend them they are the best. They know what they doing. They do a good job. I like the way they do their job.
    Jeni AriasGoogle review

Bathtub Installation Questions Houston Homeowners Ask

Still wondering? (346) 776-8560

Local service team

Book Bathtub Installation in Houston

Call (346) 776-8560 for a free estimate. We set the drain and overflow, fit the faucet, and test the tub before we leave, Monday to Sunday, 7:00 AM to 10:00 PM.

Contact El Primo Lalo Plumbing

Call us at (346) 776-8560 to book bathtub installation or ask a question. We are open Monday to Sunday, 7:00 AM to 10:00 PM, and estimates are free.

Call to book

The fastest way to book is a phone call. Tell us what is happening and we will give you a free estimate and a time that works, Monday to Sunday, 7:00 AM to 10:00 PM.

Open Mon–Sun, 7:00 AM–10:00 PM. Free estimates.