Garbage disposal repair in Houston, for jams, hums and leaks

Garbage disposal repair in Houston is the work of clearing the jam or replacing the worn seal or failed motor — and saying plainly when replacement is the honest answer. A disposal that hums but will not turn, jams every week, or leaks under the sink is usually a jam, a worn seal or a failed motor away from working again. El Primo Lalo Plumbing repairs garbage disposals in Houston, and tells you plainly when replacement is the honest answer.

El Primo Lalo Plumbing — your local Plumbing team
  • Jammed disposals
  • Humming units
  • Leaks under sinks
  • Written scope firstYou approve the price before we start
  • Tested before we leaveEvery repair gets a pressure or flow test
  • Parts on the truckCommon fittings stocked for one-visit repairs
  • Clean work areaWe haul away old parts and debris

What Our Garbage Disposal Repair Covers

Every disposal repair visit includes the diagnostic and the standard parts that fail most often. If the unit needs a full replacement, we quote that separately before any work starts so you can compare.

  • Full Diagnostic and Power TestWe cut power at the breaker, test the circuit, and check the motor, capacitor, and flywheel. You get a clear explanation of what failed and why before we quote the repair.
  • Jam Clearing and Flywheel ResetWe clear jams with the manufacturer's hex wrench or a plumber's auger and confirm the flywheel spins free. If the jam pushed debris into the P-trap, we clear that too.
  • Flange and Gasket ResealLeaks at the sink flange are common on older Houston units. We replace the mounting ring and gasket, reseat the flange with fresh putty or a wax ring, and test with a full sink of water.
  • Drain and Dishwasher Line CheckWe check the P-trap, drain arm, and dishwasher drain connection for clogs or loose fittings. New washers and Teflon tape go on any connection we open.
  • Capacitor and Electrical SwapA failed capacitor is one of the most common reasons a disposal hums without spinning. We stock common ratings on the truck and swap them on the spot when the motor is otherwise sound.
  • Leak Test and CleanupBefore we leave, we run the disposal with water, check every connection with a dry paper towel, and wipe down the cabinet. Old parts go with us.
Garbage Disposal Repair
Plumbing services in Houston | El Primo Lalo Plumbing

Disposal repair for homes

We repair disposals in houses, condos, and rentals across Houston. You get a written estimate before work starts and a dry cabinet when we leave.

  • Humming unit that will not spin
  • Water under the kitchen sink
  • Slow drain after grinding
  • Old unit that trips the breaker

Disposal repair for businesses

Restaurant and breakroom disposals take heavier loads than home units. We repair and replace them and check the drain line so service is not interrupted.

  • RestaurantsHeavy-load disposals and grease trap connections checked
  • BreakroomsOffice kitchen units repaired with minimal downtime
  • Rental propertiesDocumented repairs for property managers and owners
  • CafesSmall commercial units serviced and replaced

Garbage Disposal Repair in Houston: Jam, Seal or Motor

Disposal diagnosis splits three ways. A humming unit is usually jammed: something is caught between the plate and the ring, and the reset button and a jam key often free it. A leak under the sink is usually a seal, a flange or the drain connection. A unit that is dead, trips constantly, or leaks from the body itself is usually done, and replacement is the honest answer.

A disposal ties into the sink drain and the dishwasher connection, so a disposal problem can look like a drain problem and a drain problem can look like a disposal problem. We check the unit, the trap and the drain before deciding, because clearing a drain will not fix a jammed disposal, and replacing a disposal will not fix a blocked main.

Humming means jammed. Leaking means a seal. Dead means done. Know which before you start.

How Our Disposal Repair Process Works

Five steps from your first call to a tested, dry, working disposal. No guesswork and no surprise charges.

  1. Phone Triage

    Phone Triage

    You describe the symptom: hum, no power, leak, or slow drain. We ask the unit brand and age, then book a window that fits your day. Most Houston calls get a prompt slot, and we call ahead when the tech is on the way.

  2. Power-Off Inspection

    Power-Off Inspection

    The tech kills power at the breaker, confirms it with a tester, and pulls the unit apart enough to inspect the flywheel, shredder ring, and flange. This takes 15-20 minutes and tells us whether the motor is worth saving.

  3. Written Estimate

    Written Estimate

    You get a written estimate for the repair before any wrench turns. If the motor is burned out, we quote a replacement install side by side so you can compare repair versus new on the spot.

  4. Repair and Reseal

    Repair and Reseal

    We clear jams, swap capacitors, replace mounting rings and flange gaskets, and reseat the unit with fresh plumber's putty or a wax ring. Drain connections get new washers and Teflon tape so nothing weeps.

  5. Test and Cleanup

    Test and Cleanup

    We run the disposal with water, check for leaks under the sink with a dry paper towel, and confirm the P-trap drains fast. The cabinet gets wiped down and we haul off the old parts before we go.

Tools and Methods We Use on Disposal Repairs

  • Plumbing in Houston

    drain snake

    Clears clogs in the P-trap and branch drain when a disposal jam pushes debris downstream. We run it after clearing the unit so the sink drains fully.

  • Plumber at work in a Houston home

    Plumber's auger

    Used on stubborn clogs in the drain arm and trap. It reaches past the disposal outlet without damaging the housing.

  • Careful professional plumbing work in Houston

    Leak detection microphone

    Finds hidden drips behind the cabinet or under the floor when a disposal leak is not obvious. It saves tearing into drywall to locate the source.

  • Camera inspection before we dig

    Sewer camera

    Checks the branch drain and sewer line when a disposal backup keeps returning. It shows roots, offsets, or buildup that a snake cannot fix.

  • Plumbing in Houston | El Primo Lalo Plumbing

    Pipe cutter and tube cutter

    Cuts copper or PVC cleanly when a drain arm or supply line needs replacement during a disposal repair.

  • Plumbing parts and tools on hand

    Press fitting tool

    Makes fast, reliable joints on copper and PEX without soldering, which matters in tight cabinets where a torch is a fire risk.

  • Plumbing in Houston | El Primo Lalo Plumbing in Houston, TX

    Propane torch

    Used for soldered copper joints on older Houston homes when a press fitting is not the right call.

  • Plumbing in Houston | El Primo Lalo Plumbing in Houston, TX

    Uniform Plumbing Code compliance

    Every drain and supply connection we touch follows the Uniform Plumbing Code. That includes proper trap arms, venting, and flange sealing so the repair passes inspection and holds up.

When Houston Homeowners Call Us for Disposal Repair

  • A disposal jams during a holiday meal prep in River Oaks and the sink will not drain.

    We dispatch a prompt tech, clear the jam, check the P-trap for debris, and test the unit with a full sink of water. If the motor is fine, the repair is quick and the written estimate is quoted before we start. The sink is usable again the same day, and the homeowner knows what not to put down the drain next time.

  • A landlord in Bellaire finds water under the kitchen sink and a disposal that will not turn on.

    We diagnose a failed flange gasket and a tripped breaker, reseal the flange with a new mounting ring, and test the circuit. The tenant gets a dry cabinet and a working disposal in one visit. The repair is documented for the property file, and the landlord avoids a cabinet replacement.

  • An 11-year-old disposal in a Spring Branch home finally burns out after years of hard water scale.

    We confirm the motor winding is gone, quote a replacement install side by side with the repair cost, and install a correctly sized unit the next morning. The dishwasher drain is reconnected and tested. The homeowner gets a quieter, stronger unit with a paperwork and no old parts left behind.

  • A Clear Lake homeowner notices the disposal spins but the sink drains slowly after every use.

    We clear the P-trap, run a drain snake down the branch line, and check the dishwasher connection. The disposal itself is fine, so we do not sell a replacement. The sink drains fast again, and the homeowner saves the cost of an unnecessary new unit.

How Garbage Disposal Repair Works in Houston

Disposal repairs follow kitchen use, concentrated in family homes in Memorial and the Heights, and in Midtown and Downtown apartments where disposals work hard every day. Grease in the kitchen line is the companion problem.

  • The HeightsFamily kitchens where the disposal jams on food waste and bone fragments.
  • MontroseBungalow kitchens where an aging disposal hums, leaks or trips.
  • MidtownApartment kitchens where disposals work hard every day and jam often.
  • MemorialLarge family kitchens where the disposal and the kitchen drain clog together.
  • Galleria/UptownHigh-use kitchens where a leaking disposal seal soaks the cabinet.
  • Kitchen greaseGrease in the kitchen line is the companion problem: it coats the pipe and narrows the drain.

From problem to finished result.

  • Jammed Disposal to Fast-Draining Sink

    Before

    A River Oaks homeowner had a disposal that hummed and would not spin after a dinner party. The sink held water and the cabinet smelled. The unit had a bone fragment jammed in the flywheel and debris packed in the P-trap.

    After

    We cut power, freed the flywheel, cleared the trap, and tested the unit with a full sink of water. The repair took under an hour and cost far less than a replacement. The sink drained in seconds and the smell cleared once the trap was clean.

    Run cold water for 15 seconds before and after grinding, and avoid bones, coffee grounds, and rice. A monthly grind of ice and citrus peel keeps the ring clean.

  • Leaking Flange to Dry Cabinet Floor

    Before

    A Midtown landlord found water under the kitchen sink and a disposal that tripped the breaker. The flange gasket had failed and water was dripping onto the cabinet base, which had started to swell at the seam.

    After

    We replaced the mounting ring and gasket, resealed the flange, and reset the breaker. The full-water leak test came back dry. The repair ran a written estimate and the cabinet base dried out without replacement.

    Check under the sink monthly for moisture, and do not hang heavy items on the disposal or drain arm. A new gasket every 8-10 years prevents most flange leaks.

  • Burned-Out Motor to New Quiet Unit

    Before

    An 11-year-old 1/2-hp disposal in a Spring Branch home finally died after years of hard water scale. The motor winding was burned and the unit tripped the breaker on every reset. The homeowner was washing dishes in a bucket.

    After

    We quoted repair versus replacement and installed a 3/4-hp unit the next morning. The dishwasher drain was reconnected and tested, and the old unit was hauled off. The install ran a written estimate and the kitchen was back to normal by noon.

    Run cold water while grinding and flush the unit weekly. With Houston's hard water, a water softener will extend the new unit's life by several years.

Common Disposal Problems We Solve in Houston

Most disposal calls fall into a handful of failure patterns. Here is what we see and how we fix it.

  • Disposal hums but will not spin

    Disposal hums but will not spin

    We cut power, free the flywheel with the hex wrench, and check the capacitor. If the motor is still good, we clear the trap and test the unit. If the winding is burned, we quote a replacement install on the spot. Holding the switch on while it hums burns the motor winding and turns a simple jam clearing into a full replacement. The flywheel is usually stuck on food debris or a foreign object.

  • Water leaking from the disposal housing

    Water leaking from the disposal housing

    We identify whether the leak is at the sink flange, the drain connection, or the housing seal. Flange and gasket leaks get a reseal; a cracked housing means replacement. Every repair gets a full-water leak test. A leaking housing or flange rots the cabinet base and can warp flooring within days. Left alone, it also grows mold in the cabinet.

  • Sink drains slowly after using the disposal

    Sink drains slowly after using the disposal

    We clear the P-trap and run a drain snake down the branch line if needed. We also check the dishwasher drain connection, which is a common source of buildup, and test flow before we leave. Slow draining means solids are building up in the P-trap or branch drain. Ignoring it leads to a full clog and a backed-up sink.

  • Disposal trips the breaker or has no power

    Disposal trips the breaker or has no power

    We test the circuit, check the reset button, and confirm power at the unit. If the disposal is drawing too much current, we diagnose the motor and quote the right fix instead of guessing. A tripped breaker or dead outlet can look like a failed disposal. Misdiagnosing it leads to an unnecessary replacement.

A tested repair keeps your sink working and your cabinet dry.

  • Prompt Kitchen Recovery

    We stock common capacitors, flange gaskets, and mounting rings on the truck, so most garbage disposal repair Houston calls finish in one visit. You get your sink back before dinner instead of washing dishes in the bathtub for a week.

  • Stop Water Damage Early

    A leaking disposal housing can rot the cabinet base and warp flooring within days. Fixing a disposal leak repair Houston near me call early usually means a small repair instead of cabinet replacement and subfloor drying that runs into four figures.

  • Protect the Drain Line

    A disposal that grinds poorly sends solids into the P-trap and branch drain, which is how a simple jam turns into a clogged main drain. We clear the trap, test flow, and confirm the unit drains fully before we leave.

  • Keep a Good Motor Running

    Most 1/2-hp and 3/4-hp units last 8-12 years with proper care. If the motor spins free and only the capacitor or flange has failed, repairing it is the garbage disposal repair Houston Texas route and keeps a serviceable appliance out of the landfill.

What you receive

Clear records you can keep and share.

Flat-price quote

Approved before any work starts

Leak test

Full sink of water before we leave

Written summary

What failed and what to avoid

Repair or replace: how to decide

A disposal with a good motor and a failed capacitor or flange is worth repairing. A unit with a burned winding or a cracked housing is not.

  • Motor condition

    If the flywheel spins free and the motor hums, the winding may still be good. A burned smell or a breaker that trips on reset points to replacement.

  • Age of the unit

    Most units last 8-12 years. Past that, a repair may only buy a few months before another part fails.

  • Leak source

    A flange or gasket leak is a reseal. A crack in the housing itself cannot be repaired and means a new unit.

Local service area

Plumbing coverage in Houston

Outside these areas? Call and ask if we can reach you. (346) 776-8560

What Houston Customers Say About Our Disposal Work

  • I can't say enough about their service. They are prompt and responsive to questions. Attentive to cleaning up afterwards and wear shoe covers. Prices are good and he helped me choose compatible replacement faucet and garbage disposal. which I ran out and picked up while he did other repairs. Fransisco is such a kind person and my elderly mom has been so pleased.
    Ann BogranGoogle review
  • Great work done to perfection! And a great price.... give them a call
    Matthew MiertschinGoogle review
  • I'm very happy with your service. He is very efficient and knowledgeable thank you primo Lalo!!!
    Naty MaqueiraGoogle review

Garbage Disposal Repair Questions Houston Homeowners Ask

Still wondering? (346) 776-8560

Local service team

Book Garbage Disposal Repair in Houston

Call (346) 776-8560 for a free estimate. We find the jam, seal or motor fault, fix it, and test the disposal before we leave, Monday to Sunday, 7:00 AM to 10:00 PM.

Contact El Primo Lalo Plumbing

Call us at (346) 776-8560 to book garbage disposal repair or ask a question. We are open Monday to Sunday, 7:00 AM to 10:00 PM, and estimates are free.

Call to book

The fastest way to book is a phone call. Tell us what is happening and we will give you a free estimate and a time that works, Monday to Sunday, 7:00 AM to 10:00 PM.

Open Mon–Sun, 7:00 AM–10:00 PM. Free estimates.