Garbage disposal installation in Houston, wired, sealed and tested

Garbage disposal installation in Houston is the work of a drain connection, a dishwasher connection and a seal, not just a unit under the sink. A new garbage disposal is a drain connection, a dishwasher connection and a seal, not just a unit under the sink. El Primo Lalo Plumbing installs garbage disposals in Houston with the flange sealed, the trap connected right, and the unit tested before we leave.

Garbage Disposal Installation by El Primo Lalo Plumbing
  • New disposals
  • Drain connection
  • Dishwasher hookup
  • Written scope firstYou approve the price before we start
  • Tested before we leaveEvery repair gets a pressure or flow test
  • Parts on the truckCommon fittings stocked for one-visit repairs
  • Clean work areaWe haul away old parts and debris

What Our Garbage Disposal Installation Includes

Every install covers the removal, the new unit, the connections, and the test. Here is what is included in a standard job and what counts as an add-on.

  • Removal and Haul-AwayWe disconnect the old unit, remove it from the mounting assembly, and take it with us. The cabinet gets wiped down before the new unit goes in. You do not have to schedule a separate pickup or haul it to the curb.
  • New Disposal and Mounting HardwareThe price includes the new disposer and the mounting hardware: the flange, the gasket, the mounting ring, and the bolts. We use the manufacturer's hardware for the unit you choose. If the existing flange is in good shape, we reuse it and note that on the invoice.
  • Drain and Dishwasher ConnectionsWe connect the drain to the trap arm and the dishwasher line to the inlet. The knockout plug gets removed when a dishwasher is present. Every joint is tested with running water before we close the cabinet.
  • Electrical Connection and TestWe wire the unit to the existing circuit, confirm the breaker size and ground, and test the reset button. If the circuit is undersized or the wiring is damaged, we tell you before we proceed. Electrical work beyond the existing circuit is quoted separately.
  • Leak and Drain CheckAfter the install, we run the unit with water and check every joint for drips. We also confirm the sink drains freely. If the drain is slow, we can clear it with a drain snake or plumber's auger during the same visit.
Garbage Disposal Installation
Plumbing services in Houston | El Primo Lalo Plumbing

Disposal installs for Houston homes

We install disposals in single-family homes, townhomes, and apartments across Houston. Every visit includes a check of the flange, the drain, and the shutoff valves under the sink.

  • Leaking bottom housing
  • Motor hums but will not turn
  • Slow kitchen drain
  • Old unit replacement

Disposal work for businesses

Restaurants, break rooms, and commercial kitchens need disposals that keep up with volume. We install and service units around your operating hours so service is not interrupted.

  • RestaurantsPrep sinks and dish pits with heavy daily use
  • Break roomsOffice kitchens with light to medium use
  • RentalsTurnover swaps between tenants
  • RetailSmall kitchen areas in retail spaces

Garbage Disposal Installation in Houston: Seal, Drain and Test

A disposal install has three connections that all have to be right: the flange seal to the sink, the drain trap, and the dishwasher inlet where fitted. A bad flange seal leaks under the sink, a wrong trap connection smells, and a dishwasher inlet left plugged means the dishwasher will not drain. We test all three before we leave.

A new disposal is also the right time to look at the kitchen drain, because grease and food waste narrow the line over time. If the sink drains slowly with a new disposal, the problem is the drain, not the unit, and we check the line before the install, not after.

Flange, trap, dishwasher inlet. Get all three right and the disposal is done for years.

How Our Installation Process Works

Five steps from the first phone call to a tested, running disposal. No surprises, no guesswork.

  1. Phone Intake

    Phone Intake

    You call (346) 776-8560 and tell us what the sink is doing. We ask about the disposal brand, the sink type, and whether the unit leaks or just hums. That five-minute conversation lets us load the right size disposer and mounting hardware before we roll, which is why most jobs finish in one trip.

  2. On-Site Inspection

    On-Site Inspection

    We shut off power at the breaker and water at the shutoff valves, then inspect the flange, the trap, and the wiring. If the existing mounting ring is corroded or the dishwasher knockout is wrong, we note it before quoting. You get a firm price before any work starts.

  3. Removal and Prep

    Removal and Prep

    We disconnect the drain and dishwasher line, remove the old unit, and clean the flange surface. Old plumber's putty and rust get scraped off so the new gasket seats flat. We check the drain opening with a plumber's auger if the line looks slow, and we replace the trap arm gasket if it is brittle.

  4. Mount and Wire

    Mount and Wire

    The new disposer goes onto the mounting assembly, gets plumbed to the drain and dishwasher, and is wired to the existing circuit. We verify the breaker size and the ground before powering up. A 1/2 HP unit draws about 6 amps; a 3/4 HP draws closer to 9, so we confirm the circuit can carry it.

  5. Test and Cleanup

    Test and Cleanup

    We run the unit with water, check every joint for drips, and cycle the dishwasher drain to confirm no backup. Then we wipe the cabinet, haul the old disposer away, and walk you through what not to put down the drain. The whole visit usually runs two to three hours.

Tools and Methods We Use on Every Install

  • Plumbing services in Houston

    Pipe wrench

    Used to loosen the drain fittings and the trap arm so the old unit can be removed without damaging the pipe threads.

  • Plumbing in Houston

    Plumber's auger

    Clears the trap arm and branch drain when the sink is slow after the install. A hand auger reaches most kitchen clogs without pulling the trap.

  • Plumber at work in a Houston home

    Drain snake

    Used for longer clogs in the branch drain. The snake follows the pipe and breaks up grease and food solids that the disposal pushed down.

  • Careful professional plumbing work in Houston

    Sewer camera

    Inspects the line when the sink backs up repeatedly. The camera shows whether the clog is in the branch drain or the main sewer line.

  • Camera inspection before we dig

    Propane torch

    Used when a copper supply line or drain connection needs to be soldered. We use it only when the joint cannot be made with a mechanical fitting.

  • Plumbing in Houston | El Primo Lalo Plumbing

    Tube cutter

    Cuts copper pipe cleanly when a supply line or drain section needs to be replaced during the install.

  • Plumbing parts and tools on hand

    tools

    Our drain and pipe tools include cutters and wrenches, which hold up to daily use and make clean cuts on copper and PVC.

  • Plumbing in Houston | El Primo Lalo Plumbing in Houston, TX

    Uniform Plumbing Code (UPC) compliance

    Every install follows the UPC for the trap, the drain connection, and the dishwasher inlet. That means the trap arm is properly sized, the venting is correct, and the connection is made to code, not just to what fits.

When Houston Homeowners Call Us for Disposal Work

  • A homeowner in River Oaks is remodeling the kitchen and wants a new disposal to match the new sink and faucet.

    We coordinate with the countertop and plumbing schedule, install the disposal after the sink is set, and connect the dishwasher and drain. We confirm the cabinet space and the electrical circuit before the unit is ordered. The kitchen is ready to use the same day the countertop goes in, with no second visit needed.

  • A tenant in Midtown reports that the disposal stopped working and the sink is backing up.

    We diagnose the unit, confirm the motor has failed, and replace it with a 1/2 HP model. We also clear the trap arm, which was partially clogged with food scraps. The sink drains freely and the tenant has a working disposal the same day.

  • A family in Clear Lake is replacing a 15-year-old disposal that leaks and rattles the cabinet.

    We remove the old unit, replace the corroded flange and gasket, and install a 3/4 HP disposer with sound insulation. We check the shutoff valves and supply lines while the cabinet is open. The new unit runs quietly and the cabinet stays dry. The old unit leaves with us.

  • A property manager in the Energy Corridor needs disposals swapped in three units between tenants.

    We schedule the three installs in one morning, bring the units on the truck, and complete each swap in about 90 minutes. Invoices are itemized per unit. All three units are ready for move-in the same day, with no return trips.

How Garbage Disposal Installation Works in Houston

Disposal installs follow kitchen remodels and replacements, concentrated in family homes in Memorial and the Heights, and in Midtown and Downtown apartments. Grease in the kitchen line is the companion problem everywhere.

  • The HeightsKitchen remodels where a new disposal goes in with a new sink and faucet.
  • MontroseBungalow kitchen upgrades where the disposal, trap and dishwasher connection are renewed.
  • MidtownApartment kitchen replacements where the disposal works hard every day.
  • MemorialLarge family kitchens where the disposal and the kitchen drain are renewed together.
  • Galleria/UptownHigh-use kitchens where a new disposal has to be fitted and tested properly.
  • Kitchen greaseGrease in the kitchen line coats the pipe and narrows the drain; a new disposal will not fix a greasy line.

From problem to finished result.

  • Leaking Disposal in a Heights Bungalow

    Before

    The disposal leaked from the bottom housing into the cabinet. The sink base was damp, the flange was corroded, and the trap arm was partially clogged with food scraps.

    After

    We replaced the unit with a 3/4 HP disposer, installed a new flange and gasket, and cleared the trap arm. The cabinet was dried and tested. The sink drained freely and no leaks showed after a full cycle.

    Run cold water for 15 seconds before and after grinding, and avoid putting grease or fibrous scraps down the drain. A monthly ice-and-citrus grind keeps the chamber clean.

  • Breaker-Tripping Disposal in Meyerland

    Before

    The disposal tripped the breaker every few days. The motor hummed but would not turn, and the wiring at the switch was loose. The unit was more than 12 years old.

    After

    We replaced the disposal with a 1/2 HP unit, tightened the wiring at the switch, and confirmed the breaker size. The new unit ran without tripping, and the amp draw measured within spec.

    Do not overload the disposer with large batches of scraps. Run it in short cycles with cold water, and check the reset button if it stops.

  • Slow Kitchen Drain in Clear Lake

    Before

    The sink drained slowly after a disposal install by another company. The trap arm was clogged with grease and rice, and the dishwasher line backed up into the sink.

    After

    We cleared the trap arm with a drain snake, checked the branch drain with a camera, and reconnected the dishwasher line. The sink drained at full flow and the dishwasher cycle finished without backup.

    Flush the drain with hot water weekly and avoid pouring grease down the sink. A mesh strainer catches scraps before they reach the trap.

Kitchen Sink Problems a New Disposal Fixes

Some sink problems look like a disposal issue but start somewhere else. Here is what we see most often in Houston kitchens.

  • Disposal hums but will not turn

    Disposal hums but will not turn

    We cut power, clear the jam with the right tool, and test the motor. If the motor is weak or the windings are bad, we replace the unit. If the jam is the only issue, we clear it and check the drain for the debris that caused it. A humming motor with no movement means the flywheel is jammed or the motor is failing. Continuing to run it can burn out the motor or trip the breaker repeatedly.

  • Water leaking from the bottom of the disposal

    Water leaking from the bottom of the disposal

    We confirm the leak source, then replace the disposal. Bottom-housing leaks are not repairable. We also check the flange and trap for leaks while the cabinet is open. A leak from the bottom housing usually means the internal seal has failed. Water in the cabinet warps the sink base and can damage flooring.

  • Sink drains slowly after installing a disposal

    Sink drains slowly after installing a disposal

    We run a drain snake or plumber's auger through the trap arm and branch drain. If the clog is further down, we use a sewer camera to locate it. Clearing the line restores flow. A slow drain points to a clog in the trap arm or branch drain, not the disposal itself. Ignoring it leads to standing water and backups.

  • Disposal trips the breaker

    Disposal trips the breaker

    We check the circuit, the wiring at the switch, and the disposal's amp draw. If the motor is drawing too much, we replace the unit. If the wiring is the problem, we repair it before the new unit goes in. A breaker that trips every time the disposal runs points to a wiring issue, a failing motor, or an undersized circuit. Repeated trips are a fire risk.

A dry cabinet, a quiet grind, and a drain that flows.

  • Stop the Leaks

    A leaking garbage disposal can rot the cabinet floor and warp the sink base within weeks. We replace the mounting gasket, plumber's putty seal, and drain gasket so the new unit sits dry. Most leaks we find start at the flange or the dishwasher inlet, and both get checked during every garbage disposal installation services Houston call.

  • End the Jam Cycle

    If you are resetting the breaker or reaching for an Allen wrench every week, the motor is on its way out. A new 3/4 HP unit grinds through everyday scraps without stalling. We size the motor to your cooking habits, so a family that cooks rice and stews daily gets more torque than a condo owner who mostly reheats.

  • Protect Your Drain Line

    A failing disposal sends food solids into the P-trap and the branch drain, which is how clogged main drain calls start. Installing a new unit with a properly seated baffle and a clean trap keeps scraps out of the line. We also check the drain snake reach and flow before we button up the cabinet.

  • Quieter Kitchen

    Older disposals rattle the whole sink cabinet. Modern units with sound insulation and a balanced grind chamber run noticeably quieter. We set the unit level and tighten the mounting ring so vibration stays in the disposer, not in your countertop. Most customers tell us the new unit is the quietest part of the kitchen afterward.

What you receive

Clear records you can keep and share.

Written quote

Price confirmed before work starts

Tested install

Every joint checked for leaks

Haul-away

Old unit removed and taken away

What to know before you replace a disposal

The unit is only one part of the job. The flange, the drain, and the electrical circuit decide how long the install takes and how well it holds up.

  • Flange condition

    A corroded flange will leak even under a new unit. We check it before quoting. If it is pitted or seized, it gets replaced.

  • Drain flow

    A slow drain is a sign of a clog, not a bad disposal. We test the flow and clear the trap arm if needed. Installing a new unit over a clogged drain just moves the problem.

  • Circuit size

    A 3/4 HP unit draws more current than a 1/2 HP model. We confirm the breaker and wire gauge before wiring. If the circuit is shared, a dedicated line may be needed.

Local service area

Plumbing coverage in Houston

Outside these areas? Call and ask if we can reach you. (346) 776-8560

What Houston Customers Say

  • I can't say enough about their service. They are prompt and responsive to questions. Attentive to cleaning up afterwards and wear shoe covers. Prices are good and he helped me choose compatible replacement faucet and garbage disposal. which I ran out and picked up while he did other repairs. Fransisco is such a kind person and my elderly mom has been so pleased.
    Ann BogranGoogle review
  • I'm very happy with your service. He is very efficient and knowledgeable thank you primo Lalo!!!
    Naty MaqueiraGoogle review
  • I will definitely recommend them they are the best. They know what they doing. They do a good job. I like the way they do their job.
    Jeni AriasGoogle review

Garbage Disposal Installation Questions Houston Homeowners Ask

Still wondering? (346) 776-8560

Local service team

Book Garbage Disposal Installation in Houston

Call (346) 776-8560 for a free estimate. We seal the flange, connect the drain and dishwasher inlet, and test the disposal before we leave, Monday to Sunday, 7:00 AM to 10:00 PM.

Contact El Primo Lalo Plumbing

Call us at (346) 776-8560 to book garbage disposal installation or ask a question. We are open Monday to Sunday, 7:00 AM to 10:00 PM, and estimates are free.

Call to book

The fastest way to book is a phone call. Tell us what is happening and we will give you a free estimate and a time that works, Monday to Sunday, 7:00 AM to 10:00 PM.

Open Mon–Sun, 7:00 AM–10:00 PM. Free estimates.