Written price
Full price before work starts
Faucet installation in Houston is the work of fitting the faucet level, sealing it cleanly, and checking the supply lines and shutoff valves behind it. A new faucet should sit level, seal cleanly, and shut off fully, with supply lines and shutoff valves that work. El Primo Lalo Plumbing installs kitchen and bathroom faucets in Houston, and checks the lines and valves behind them at the same time.
Every faucet installation includes the labor to remove the old fixture, set the new one, connect the supply lines, and test for leaks. We also check the shutoff valves and drain assembly while we are under the sink. Parts like a new supply line or a replacement angle stop are quoted before we install them, so you know the full price up front.


We install kitchen and bathroom faucets in houses, townhomes, and apartments across Houston. Every visit includes a shutoff valve check and a leak test before we leave.
We install commercial-grade faucets in break rooms, restrooms, and kitchens. Work can be scheduled during business hours so tenants are not disrupted.
A faucet install is three jobs: the fixture, the supply lines and the shutoff valves. Old shutoffs often do not shut off, and a corroded supply line is the leak waiting to happen behind a new faucet. We check both before the new faucet goes on, because a new fixture on a failed valve is a callback, not a finished job.
Houston's hard water, about 8 grains per gallon on average, is why we talk about cartridges and aerators at install time. A faucet that is easy to service lasts longer here than one that is not. Remodel work in older homes often means new supply lines too, especially where galvanised pipe is still in place.
A new faucet on a failed shutoff is a callback, not a finished job.
Every job follows the same five steps, whether it is a single bathroom sink in Montrose or a full kitchen faucet replacement Houston TX in a River Oaks home. Here is exactly what to expect from the moment we arrive.

Cuts copper pipe and PEX tubing cleanly when a supply line or stub-out needs to be shortened or replaced. A clean cut is the difference between a leak-free joint and a call-back.

Connects push-fit and expansion fittings to copper or PEX without soldering. It is faster and safer in tight cabinet spaces where a propane torch is a fire risk.

Used for soldered copper joints when the code or the situation calls for a brazed connection. We keep a fire-rated pad on hand and follow local code on when soldering is allowed.

Loosens seized supply lines, angle stops, and drain fittings. A proper pipe wrench gives the leverage to break a corroded nut without cracking the sink or the valve body.

Clears clogs in the P-trap and branch drain when a new faucet is installed on a sink that drains slowly. It is the right tool for a small clog before it becomes a main-line problem.

Finds hidden leaks in the wall or under the slab when a faucet problem turns out to be a supply line leak behind the cabinet. It saves tearing into drywall to find the source.

Every install follows the code standards for supply line sizing, shutoff valve placement, and drain connections. That matters when you sell the house or when an inspector looks under the sink.

We replace the supply lines and check the angle stops on every install. A new faucet on old, corroded supply lines is a leak waiting to happen, and the parts cost less than a water damage repair.
We replaced the angle stops with quarter-turn valves, installed the new kitchen faucet, and connected the sprayer and soap dispenser. The whole job took about 2 hours, including the valve replacement. The homeowner got a working shutoff, a leak-free faucet, and a kitchen that was ready for the countertop install the next day.
We pulled the old faucet, cleaned the deck, installed a new bathroom faucet with fresh supply lines, and replaced the drain assembly. The job took 75 minutes. The drip stopped, the stain stopped spreading, and the homeowner's water bill dropped by a large amount a month.
We scheduled the work for 6 p.m., installed commercial-grade faucets in three break rooms, tested every connection, and hauled the old fixtures away. The property manager had working faucets by morning and no disruption to the tenants during business hours.
We cut the seized nut with an oscillating tool, cleaned the deck, and installed the new faucet with new supply lines. The job took 90 minutes. The homeowner avoided a return trip to the store and got the faucet installed in one visit.
Remodel-driven installs concentrate in the Heights, Montrose and River Oaks, where older homes get new kitchens and baths, and in Memorial where family kitchens are upgraded. Hard water makes serviceable cartridges worth choosing.
A homeowner in Bellaire bought a new kitchen faucet but could not shut the water off under the sink. The original 1960s angle stop was seized open, and the supply line was corroded.
We replaced both angle stops with quarter-turn valves, installed the new faucet with fresh supply lines, and tested every connection. The job took 2 hours and the water bill dropped by a large amount a month.
Turn the shutoff valves open and closed once a year to keep them from seizing. If a valve feels stiff, call us before it fails.
A Montrose homeowner had a bathroom faucet that dripped constantly and stained the sink basin. The cartridge was worn out and the drain assembly was loose.
We installed a new bathroom faucet with a new drain assembly and fresh supply lines. The drip stopped, the stain stopped spreading, and the job took 75 minutes.
Wipe the faucet dry after use and clean the aerator every six months to keep scale from building up.
A property manager near the Medical Center had three break room faucets that leaked at the base and would not swivel. Tenants had been complaining for weeks.
We installed commercial-grade faucets in all three break rooms during business hours, tested every connection, and hauled the old fixtures away. The work was done by 9 p.m. and the tenants had working faucets the next morning.
Schedule a yearly check on commercial faucets and shutoff valves to catch wear before it turns into a leak.
A faucet problem is rarely just a faucet problem. It is usually a sign of something else under the sink. Here are the most common issues we find when we arrive for a faucet installation near me Houston TX call.

We diagnose the cartridge first. If a or cartridge is available, we rebuild the faucet. If the body is cracked or the parts are obsolete, we install a new faucet and replace the supply lines at the same time. A steady drip wastes 3,000 gallons a year and can stain the sink basin. The cause is usually a worn cartridge or O-ring, and the fix is often a rebuild or a full replacement if the body is corroded.

We remove and clean the aerator, check the shutoff valve, and test flow at the supply line. If the valve is the problem, we replace it. If the line is clogged with scale, we flush it before installing the new faucet. A clogged aerator or a failing shutoff valve can cut flow to a trickle. If the problem is in the supply line, it can spread to other fixtures.

We pull the faucet, inspect the supply lines and drain, and reinstall it correctly with fresh Teflon tape and new gaskets. If the cabinet floor is wet, we dry it and check for mold before closing up. A cross-threaded supply line or a missing gasket can leak slowly and rot the cabinet floor. By the time you smell it, the damage is already done.

We replace the angle stop with a new quarter-turn valve. That gives you a working shutoff under the sink and makes the next faucet repair a 20-minute job instead of a 2-hour one. If the valve will not close, you cannot shut the water off to the faucet. That turns a simple repair into a whole-house shutoff and a bigger job.
A dripping faucet wastes 3,000 gallons a year or more, and the damage happens under the sink where you cannot see it. We replace the supply lines and check the shutoff valves during every install, so the cabinet stays dry and the water bill stops climbing.
Old aerators and clogged cartridges cut flow to a trickle. A new EPA WaterSense-rated faucet restores strong flow at 1.5 gallons per minute or less, which saves water without sacrificing pressure. Most customers notice the difference the first time they turn the handle.
We install to the 2021 Uniform Plumbing Code with Houston Amendments standards, using push-fit or expansion fittings where they belong and brazed copper where code requires it. That matters when you sell the house or when an inspector looks under the sink.
Most standard faucet replacements take 1 to 2 hours. We bring the wax rings, supply lines, Teflon tape, and common adapters on the truck, so you are not making a second trip to the hardware store while the water is off.
Clear records you can keep and share.
Full price before work starts
Every connection checked
We take the old faucet with us
The faucet is only half the job. The shutoff valves and supply lines under the sink matter just as much, and they are the most common reason a simple swap turns into a bigger repair.
If the angle stops are seized or weeping, replace them during the install. A working shutoff makes the next repair a 20-minute job instead of a 2-hour one.
Old supply lines can crack or clog. New lines cost little and prevent a leak that can rot the cabinet floor.
Check the hole spacing and deck thickness before buying. A faucet that does not fit the sink means a second trip to the store.

Outside these areas? Call and ask if we can reach you. (346) 776-8560
A plumber should install a faucet, especially when the job involves new supply lines or shutoff valves. The tie-in to the water supply is permanent work, and a bad connection leaks inside a cabinet where nobody sees it until the floor is damaged.
A straightforward swap is usually a short visit. The job takes longer when shutoff valves or supply lines also need replacing, which is common in older Houston homes. We give you a written scope before we start.
Yes, if they are old, corroded or do not shut off fully. A new faucet on a failed valve is a callback waiting to happen, and replacing the valve while the faucet is out costs far less than a second visit.
Yes. Estimates are free, and you approve the written scope before work starts. We are open Monday to Sunday, 7:00 AM to 10:00 PM.
Call (346) 776-8560 for a free estimate. We fit the faucet, check the supply lines and valves, and test everything before we leave, Monday to Sunday, 7:00 AM to 10:00 PM.
Call us at (346) 776-8560 to book faucet installation or ask a question. We are open Monday to Sunday, 7:00 AM to 10:00 PM, and estimates are free.
The fastest way to book is a phone call. Tell us what is happening and we will give you a free estimate and a time that works, Monday to Sunday, 7:00 AM to 10:00 PM.
Open Mon–Sun, 7:00 AM–10:00 PM. Free estimates.